Enclosures & electronics

Configure a custom desk cable grommet online and adjust Diameter, Thickness, Specific dimension and Wall thickness to your application.

Configure a custom cable holder online and adjust Diameter and Specific dimension to your application.

Configure a custom housing with lid online and adjust Length, Width, Height and Wall thickness to your application.

Configure a custom housing online and adjust Specific dimension and Wall thickness to your application.

Customizable Y adapter for splitting cable conduits, cable ducts and protective tubes.

Customizable cable passthrough with round flange and four screw holes.

Custom adapter for monitor stands and display mounts.

Make a dust filter for a custom PC vent: set the opening, frame and magnet pockets. Uses separate filter mesh and a flat steel case mounting surface.

Custom wall mount adapter for tool chargers, power supplies and battery stations.

Customizable zip tie mount with central screw hole.

Electronics enclosure with eight essential settings, including the width and length of the installed circuit board or module.

Two-piece cord spooler with guided rail connection and four grip cutouts.

Attach a new separate cushion to an intact headphone headband. Match flexible carrier length, width and strap positions to your band.

Fit a passive speaker terminal panel: configure cup size, recess depth, fixing pattern and two binding-post holes. Designed for separate insulated posts.

Lost a battery cover? Configure a flat replacement for straight sliding grooves, with custom length, width, side tongues and an end stop.

Create a Keystone panel for furniture or custom enclosures: set overall size, one to six ports and mounting margins. Modules and fasteners are separate.

Parametric PCB enclosure with terminal openings and separate 35 mm DIN-rail slide shoe.

Electronics enclosure with display cutout, up to six buttons and desktop, wall or panel mounting.

Ventilated sensor wall enclosure with custom PCB mounting pattern, sensor opening, cable access and three mounting styles.

Two-part screw-fastened PCB enclosure with a real four-hole mounting pattern, automatic internal heights, cable opening and optional ventilation.

Parametric WLED enclosure with separate controller and PSU compartments, 1–8 LED outputs and wall, desktop or DIN mounting.

Guide a short SMD component tape while manually peeling its cover film.

Hold a bare PCB flush for solder paste printing: customise board size, thickness and alignment pin positions, with a removal recess and wide surround.

Configure a stand to fit your headband and ear cups: set clearance height, saddle depth and base dimensions. A wide curved saddle supports the band.

Guide a mouse cable above the desk: choose reach, height and cable diameter.

Rest a cased phone on two raised supports. Set device width, cradle gap and clearance below the charging port.

Cover the camera opening mechanically: adjust bezel thickness, cover width and front depth.

Route a flat cable with clearance along a mounting surface. Parametric STL model with adjustable dimensions for 3D printing.

Make a T cover for cable trunking with different main and branch widths. Set dimensions and overlap for insulated data or extra-low-voltage cable routes.

Broken headphone band? Configure a two-piece curved splint to band width, thickness and radius, for a suitable exposed section with a soft liner.

Configure a custom speaker adapter ring with your inner diameter, height and two bolt circles. Includes a measuring guide and a printable 3D model.

Cover a rectangular LED channel end while routing its cable. Parametric STL model with adjustable dimensions for 3D printing.

Screw-mounted multi-cable clamp with adjustable diameter, quantity, spacing, opening and screw dimensions.

Custom power strip mount using only five inputs: housing width, height, clearance, holder depth and material thickness.

Compact snap holder for multiple equal-size cables, PTFE tubes or pneumatic lines.

Parametric wall mount with a clean U-shaped pocket, two countersunk holes and adjustable length, device clearance, retaining lip and material thickness.

Align a door or window contact sensor with a custom spacer. Set the height, footprint and offset, then choose adhesive or screw mounting for 3D printing.

Park a matched round sensor cable neatly on a surface. Parametric STL model with adjustable dimensions for 3D printing.

Aim your video doorbell with a custom wedge. Set horizontal and vertical angles, separate front and wall hole spacing, and an optional cable opening.

Direct sound from a bottom phone speaker toward the front.

Move several miniatures together on the gaming table. Set actual base diameter, rows, columns and spacing.

Gently align two lead rows with custom lower channel width, working length and entry allowance.