Crafts & design

Configure a custom keychain online and adjust Text, Width, Height and Thickness to your application.

Configure a custom name badge online and adjust Name, Text, Specific dimension and Height to your application.

Configure a custom text keychain online and adjust Text, Specific dimension and Thickness to your application.

Configure a custom stamp online and adjust Text to your application.

Centre a thread cone on an existing vertical spool pin with custom taper, height and bore. Check thread routing and the stability of the original stand.

Fill a small sewing-table gap: customise outer size, thickness and open machine cutout. For an existing supporting rebate and a simple free-arm shape.

Tension your own sewing tapes while stitching small book sections.

Size the working area and rib spacing for a small felting project.

Combine three of your own dry-felting needles in one handle.

Flexible cross-slit lid wipes vinyl scraps from a weeding hook into your existing collection jar.

Elliptical tapered mandrel for forming pottery spouts from damp clay slabs.

Free-hanging weight for separating embroidery floss, with two holes for your own soft tie loop.

Three eye-ended prongs for transferring neighboring stitches at your machine's needle pitch.

Clampable hackle base with a row of deep pin sockets for preparing and blending small amounts of fiber.

Fill spare palette spaces: set outside length, width and height.

Guide yarn while crocheting: adjust finger opening, band width and yarn eyelet.

Store matching thread together: choose both core diameters and bobbin height.

Replace a missing button: set diameter, thickness and thread-hole size. Round shape with a shallow thread recess.

Replace an external pin: set mounting diameter, spool shaft and free length.

Enclose bristles without contact: adjust ferrule diameter, inside length and tip clearance.

Hang a shaving brush bristles down: match fork width, seat depth and clear height to your brush. Wide base with a drainage opening.

Replace a lost rib tip: adjust bore, insertion depth and wall thickness.

Wind a soft measuring tape neatly: configure core, usable width and flange size.

Sort pre-cut embroidery threads by colour: adjust eyelet count, hole size and card height. A blank strip provides room for labels.

Support a small inverted leather-hard pot while gently trimming its foot.

Take the outside width of a rounded pottery vessel and transfer it to your own ruler.

Shape a wheel-thrown cup to your own outer profile: set height, foot and rim diameters. A flat pottery rib with a grip hole and measuring guide.

Die for a small manual clay extruder: set disc diameter, thickness and rounded rectangular opening to match your die holder and desired profile.

Cut ovals from soft modelling clay: configure two axes and height.

Roll even clay slabs: set rail height, length and width. One flat guide rail as an STL; print twice for a pair.

Transfer finished dimensions to wet clay using your shrinkage rate.

Emboss regular grooves in soft clay: choose diameter, roller length and rib spacing.

Drape an evenly rolled clay slab over this round mould and press gently into contact.

Slice soft clay parallel to the worktop with your own wire.

Fit the grip and wire seats to your soft-clay loop tool.

Cut a defined bevel along the upper edge of a soft clay slab.

Pick up a pre-aligned row of diamond-painting drills using a shared wax channel.

Register successive print colours using two pre-punched paper tabs.

Rest a small printmaking roller on its exposed axle ends so its inked surface stays clear of the bench.

Match the internal size and depth to your sponge and palette paper. Tray and overlapping lid.

Create a deliberately irregular torn edge on paper for cards, prints or small book projects.

This round insert provides rounded ribs for gently washing brushes in your own jar.

Choose trough width, depth and height to fit a small screen frame.

Judge framing and proportions through nine open fields.

This pouring cup holds three acrylic colours in separate chambers and releases them through three adjacent spouts when tilted together.

Hold a separate round felt insert in a custom carrier.

Store sewing bobbins in individually sized round pockets. Parametric STL model with adjustable dimensions for 3D printing.

Rest a round brush handle in a matching open trough. Parametric STL model with adjustable dimensions for 3D printing.

Thread a slider onto continuous zipper tape: size the support slot to the pull tab and secure the jig with two screws to a suitable work board.

Align two separated zipper tapes side by side during preparation. Parametric STL model with adjustable dimensions for 3D printing.

Separate a rectangular frame corner from the table when resting it. Parametric STL model with adjustable dimensions for 3D printing.

Mark evenly spaced attachment positions for fabric loops. Parametric STL model with adjustable dimensions for 3D printing.

Set hollow radius, opening angle and length for small bookbinding projects.

Size the jaws, working height and initial gap for small hand-sewing projects.

Guide sewing or bookbinding thread across your own cold wax puck.

Transfer a pattern line through your own tracing paper as a sequence of small pressure marks.

Guide small portions of stuffing into narrow fabric parts.

Press separately guided lace pins into a suitable lace pillow with controlled hand pressure.

Leave space between fabric and button while sewing.

Add your own fine wire loop to this flat grip to thread hand-sewing needles.

Guide the fabric edge at a distance you set from the needle.

Enclose the closed bottom end of a zipper on a lightweight fabric pouch.

Refresh the edge of tailor’s chalk in a V-shaped trough.

Cover your own suitable button blanks with fabric.

Guide evenly spaced hand stitches around your fabric circles.

Turn a sewn fabric tube that is closed at one end.

Match pressing area to leaves, flowers and your paper layers.

Emboss paper by hand or cup small paper petals on a suitable soft mat.

Size the mounting face to your rubber stamp and choose the grip height.

Two inside corners with arm lengths and height suited to your stamp blocks.

Freestanding 3D word sign with two selectable fonts and separate preview colors for main and secondary text.

Freestanding 3D heart with ECG line, names, optional date, six fonts and three selectable preview colours.

Personalised 3D word sign with two text rows, symbol and five fonts.

Custom bookmark with name and symbol for books and gifts.

Custom name sign for doors, kids rooms, offices or homes.

Custom travel tag for luggage, backpacks, bags and carry-on items.

Custom nameplate for mailboxes, doorbells, apartments, offices and front doors.

Custom name keychain for keys, bags or gifts.

Custom dog or cat tag with name and phone number.

Modern WiFi display stand with network name and password.

Gently push a still-loose knot towards the preceding bead while the open slot holds the single thread.

Guide fine soft wire at your chosen coil pitch.

Size the rollers and axle spacing for small hand-worked jewellery wire.

Fit the jump-ring opener to your finger and soft jewellery wire.

Separate mixed round beads using an opening size of your choice.

This two-part threading aid has a bowl with a central grip and a separate spindle base.

Guide a soft decorative cord end through loosely opened braid.

Twist three yarn strands together for a decorative cord.

Match the rocker blotter to your blotting paper and writing area.

Draw five parallel lines using your own matching pen refills.

Protect nearby pencil lines while erasing selected areas.

Draw a repeatable S-curve with your own length and offset.

Tooth counts and module set the curve ratio and drawing scale.

Compare visible yarn twist against three recessed sloping lines.

Add light adjustable thread drag to a manual yarn-winding station.

Lay several embroidery strands or narrow ribbons side by side while tightening a stitch.

Stretch your fabric across a round embroidery opening sized for your work.

Wrap yarn closely side by side around the narrow bar between the two stops without stretching it.

Place an already tightly tied pom-pom between the two round discs.

Guide three pre-twisted strands as you lay them into a cord by hand.

Repeat heddle length and central eyes while tying.

Keep a small handwoven fabric at an even width near the latest woven row.

Pierce folded book signatures for sewing: configure cradle length, opening width and V angle, with an end stop and longitudinal clearance slot for an awl.

Line up drills and pour them back: match tray size, ridge spacing and spout to your diamond painting drills.

Set the width, grip height and working-edge thickness. 3D-print the STL and add a separate felt strip.

Configure a spool cap for a smooth spool pin. Adjust the disc, bore and hub dimensions in an STL for 3D printing.

Keep a ball of yarn in a bowl sized for it: set inside diameter, height and guide width. Load the bent side slot from above.

Wind centre-pull yarn balls by hand: choose winding length, core diameter and grip size.

Plan a base for small crochet baskets and bags. Set width, straight middle length, hole spacing and hole diameter.

Add a fuller grip to a thin crochet hook: choose bore, grip length and middle diameter. Round through bore.

Block granny squares at four corners: set post spacing, thickness and usable height for your crochet project.

Build a hand spindle: adjust outside diameter, shaft bore and thickness. Whorl with six openings and two yarn notches.

Manage bobbin-lace thread: adjust overall length, winding shaft and handle diameter.

Match a braiding disc to your yarn and hand size: set diameter, centre hole, slot count and slot width. For decorative cords.

Make yarn cords: adjust tine spacing, tine length and handle length.

Bridge bulky fabric seams: adjust height, support width and fork opening.

Keep loose thread ends on individual stored bobbins. Set clip diameter and width to match your bobbin shape.

Trace a pattern edge at a consistent offset: set allowance, pencil opening and disc thickness. Round wheel with a central pencil funnel.

Adjust yarn capacity and grip: choose length, width and central winding gap.

Roll paper strips by hand: set mandrel diameter, winding length and handle length. Open slot for large-hole paper beads.

Mark hexagons to match your quilt: set side length, seam allowance and thickness. Open template ring as a printable STL.

Arrange beads in a circle before threading. Match the ring diameter and groove width to the bracelet and beads you plan to use.

Weave bracelets and small bead bands on a one-piece frame. Configure working length, beads per row and warp spacing.

Rest a brush over a paint container: set rim spacing, rim gap and handle cradle. Bridge with two slip-on ends and one rest.

Let paper coils relax to repeatable diameters. Choose the smallest size, size increment, number of wells and depth.

Roll paper strips into larger coils: choose tip diameter, slot length and grip size.

Compare unmarked knitting needles: set starting diameter, size increment and plate thickness.

Park two matching knitting needle tips together and help retain stitches. Match the holes and insertion depth to your needles.

Set peg count, peg circle and working height for small circular knitting projects. One-piece ring with inward-facing hook grooves.

Pack weft on a hand loom: set tooth pitch, tooth length and thickness. Nine rounded teeth with a broad grip.

Anchor sewing tapes beneath your sewing-frame slot with custom span, tape support and thickness.

Align drill rows: choose working width and peg size for your pen. STL or 3D printing.

A removable wick guide with curved stops matched to your vessel rim.

Set rod spacing, bore and bridge thickness for a hairpin lace loom. STL or one printed bridge.

Assemble loose type into lines: choose clear line width, bed depth and wall height online.

Gently pack woven rows: choose tongue width, working length and handle for your weave.

Transfer block prints by hand with a custom base diameter, grip width and grip height.

Match marbling patterns to your bath: set bar length, pin pitch and bore for your own pins.

Count stitches and rows in a custom window with 10 mm ticks.

Hand-press seams with a custom wheel diameter, width and handle length. Two-part STL or printed kit.

Repeat picot spacing: set starting width, increment and thickness. STL or printed tool.

Two open frames for small paper sheets using your own fitted mesh.

Shorten exposed needle length: set bore, sleeve length and foot diameter. STL or 3D printing.

Choose tassel length: set winding length, frame width and thickness.

Shape paper coils in three dimensions: choose diameter, curve and base thickness.

Pre-shape paper strips into waves: set pitch, height and strip width.

Choose the opening, disc size and thickness for drafting your fibre.

Form pleats by hand with custom tine spacing, length and thickness for your fabric.

Temporarily hold cane ends during hand weaving: set taper diameter, working length and grip head.

Repeat vessel dimensions with custom crossbar width and depth. STL or printed gauge.

Adapt length, shaft width and thickness to larger heddles and warp yarns. STL or printed part.

Select warp threads: set length, width and thickness for your loom. STL or printed tool.

Set clear span, paper clearance and rest width for detailed drawing.

Draw an ellipse with custom semi-axes.

Transfer a traced contour at a scale factor fixed by the geometry.

Transfer parallel lines while drawing by holding one ruler and moving the other, then alternating.

Transfer drawing distances at your chosen fixed ratio.